- All Balls Bearings and Components

ATV Rear Axle Bearings

SAFETY FIRST: Protective gloves and eyewear are recommended at this point.

Note: These instructions are very general, and you should have a service manual for your particular vehicle to get a better understanding of your particular setup and have factory recommended torque levels and specifications on hand.

Check out the Additional Service Information Resources [1] for more information on finding service information for your specific vehicle.

If you are replacing axle carrier bearings see the ATV Axle Carrier Bearings [2] guide.

Prep

Thoroughly clean the vehicle to make the job easier and prevent contamination of the new components during installation.

AB-trx350_0064

Get your steering bearing kit from ALL BALLS RACING [3].

AB-trx350_0065

Remove the contents of your ALL BALLS RACING rear axle bearing rebuild kit. Layout the components in an organized manner for easy installation.

Place the new bearings in the freezer for about an hour before installing them.

Axle Housing

AB-trx350_0040

Remove the axle housings and axle from the final drive unit.

AB-trx350_0066

Remove the dust seals with a seal pick or flat blade screwdriver.

AB-trx350_0067

AB-trx350_0068

Remove the bearing from the axle housing with a suitable bearing puller or drive it out from the opposite side.

AB-trx350_0070

Clean away all of the old grease, grime, and rust from the bearing bore.

AB-trx350_0071

Inspect the bearing bore for wear and damage. Make sure the bore is free of damage or burrs that may cause the new bearings to hang during installation.

AB-trx350_0069

Install the new bearing into the axle housing.

AB-trx350_0072

Drive the bearing in until it is fully seated or to the OEM specified depth. Use a suitable driver or socket that only applies force to the outer race of the bearing.

AB-trx350_0074

Apply grease to the lips of the dust seal.

AB-trx350_0073

Install the dust seal into the axle housing.

AB-trx350_0075

AB-trx350_0076

Push the dust seal in so that it fits flush or as otherwise specified by the OEM.

Drum Brake

Panel

AB-trx350_0033

Remove the hub nut, brake drum cover, brake drum, and shoes. Remove the brake drum panel from the axle housing.

AB-trx350_0077

Remove the dust seal with a seal pick or flat blade screwdriver.

AB-trx350_0078

AB-trx350_0079

Remove the snap ring with snap ring pliers.

AB-trx350_0080

Heat the brake panel around the area of the bearings with a heat gun.

AB-trx350_0081

Drive the bearings out.

AB-trx350_0082

Clean away all of the old grease, grime, and rust from the bearing bore.

AB-trx350_0083

Inspect the bearing bore for wear and damage. Make sure the bore is free of damage or burrs that may cause the new bearings to hang during installation.

AB-trx350_0084

Take the bearing out of the freezer and install it into the brake panel.

AB-trx350_0085

Drive the bearing in so that it is fully seated. Use a suitable driver or socket that only applies force to the outer race of the bearing.

AB-trx350_0086

Install the second bearing in the same manner as the first.

AB-trx350_0088

AB-trx350_0089

Use snap ring pliers to install the snap ring into its groove to secure the bearings.

AB-trx350_0090

Apply grease to the lips of the dust seal.

AB-trx350_0091

AB-trx350_0092

Install the dust seal over the bearings so that it fits flush or to the OEM specified depth.

Drum Cover

AB-trx350_0093

AB-trx350_0094

AB-trx350_0095

AB-trx350_0096

Remove the old dust seal from the brake drum cover.

AB-trx350_0097

Clean up the seal area.

AB-trx350_0098

Inspect the seal area for damage.

AB-trx350_0099

Apply grease to the lips of the new dust seal.

AB-trx350_0100

Install the new dust seal into the brake drum cover.

AB-trx350_0101

AB-trx350_0102

Drive the seal into place with an appropriate driver that matches the outside diameter of the seal.

AB-trx350_0040

AB-trx350_0033

Assemble the vehicle. Replace any other seals with new items as necessary or as indicated by the OEM.

Tighten the fasteners to specification and Install new cotter pints with the hub nuts.

YZ450_2010_0934

INSTALL ALL BALLS RACING STICKER!

URLs in this post:

[1] Additional Service Information Resources: http://www.cyclepedia.com/manuals/online/cpp-all-balls/additional-service-information/

[2] ATV Axle Carrier Bearings: http://www.cyclepedia.com/manuals/online/cpp-all-balls/installation-guides/atv-axle-carrier-bearings/

[3] ALL BALLS RACING: http://www.allballsracing.com/

Copyright © 2014 All Balls Bearings and Components. All rights reserved.