- All Balls Bearings and Components

Motorcycle Wheel Bearings

SAFETY FIRST: Protective gloves and eyewear are recommended at this point.

Note: These instructions are very general, and you should have a service manual for your particular vehicle to get a better understanding of your particular setup and have factory recommended torque levels and specifications on hand.

Check out the Additional Service Information Resources [1] for more information on finding service information for your specific vehicle.

 

Removal

ALL-BALLS_0004

Remove the left wheel spacer.

ALL-BALLS_0005

Remove the right wheel spacer.

Clean the outer wheel spacers and inspect them for wear on either end as well as wear on the outer surface where it makes contact with the seal. If the spacers are excessively worn they should be replaced.

ALL-BALLS_0013

Remove the brake disc to avoid damaging it while replacing the wheel bearings.

ALL-BALLS_0006

Remove the dust seals with a seal pick or flat blade screwdriver. Take care to avoid damaging the hub.

ALL-BALLS_0007

Check the bearings for rough action or looseness by turning them with your finger. If they feel loose or resist turning, replace them with new bearings.

Kawasaki_KLX140_0786

Check for any snap rings or bearing retainers.

Kawasaki_KLX140_0787

Remove the snap ring from its groove with snap ring pliers.

CRF450_1530

Honda CRFs use a a threaded bearing retainer that calls for a special wrench for removal. A punch can be used for removal, but take care to avoid damaging the hub. The special wrench will be needed to properly torque the retainer on installation.

ALL-BALLS_0017

Use a suitable bearing puller to remove the bearings.

ALL-BALLS_0014

If a bearing puller is not available, a long punch with a good edge and hammer can be used to remove the bearings. Insert the punch into the wheel and catch the edge of the bearing on the other side.

ALL-BALLS_0018

Using a hammer, hit the punch and work around the entire circumference of the bearing. The bearing will eventually be pushed out of the wheel hub.

Note: The bearings will be damaged during the removal process and should not be reused. The hammer blows transmit their impact through the balls causing small flat spots, which will cause the bearing to quickly fail if reused.

ALL-BALLS_0019

With one bearing removed, pull the inner spacer out of the hub. The second bearing can be removed using a punch, a long socket or other suitable driver.

ALL-BALLS_0021

Inspect the condition of the inner spacer. Check the bore to make certain it is clean and the axle easily passes through it.

ALL-BALLS_0020

Check each end for wear and burrs. The edges must be square to seat properly against the new bearings. If the old bearings failed it is a good idea to confirm that the center spacer has not been damaged. Make sure the inner space is the same length or slightly longer than the bearing stops in the hub or carrier.

ALL-BALLS_0031

Clean and inspect the wheel hub. Remove any dirt and corrosion. Make certain not to remove metal. This will adversely affect bearing fit.

 

Installation

ALL-BALLS_0001

Select the appropriate wheel bearing and seal kit from ALL BALLS Racing [2]. All Balls also has wheel spacer replacement kits.

To make the bearings fit easier, place the new bearings in the freezer for about an hour before installing them.

ALL-BALLS_0022

Apply a light coat of grease to the outer bearing race to aid installation.

ALL-BALLS_0015

Heating the wheel hub will cause the hub to expand slightly and will make bearing installation easier.

ALL-BALLS_0023

Set the first bearing in place with the manufactures markings facing out. If the hub has a snap ring or some other type of bearing retainer, always install that side bearing first.

ALL-BALLS_0024

Apply pressure ONLY to the outer race of the bearing. Apply pressure evenly so the bearing remains square to the wheel hub.

WR250R_0901

Use a suitable bearing driver that has the same outside diameter as the bearing. Drive the first bearing into place so that is fully seated in the hub.

ALL-BALLS_0025

If a special bearing driver tool is not an option, a socket with the same outside diameter as the bearing can be used as a substitute.

ALL-BALLS_0019

Flip the wheel over. Install the inner spacer.

Wheel_Bearing_Install-1

Install the second bearing with a suitable driver with the same outside diameter as the bearing. Drive the second bearing in until the inner race just touches the center spacer (See fig 1).

 

Wheel_Bearing_Install-2

Fully seating the second bearing may cause both bearings to become side loaded causing premature failure (See fig 2).

Wheel_Bearing_Install-3

If the center spacer is loose after the second bearing is installed, this may be a sign that the center spacer is too short and needs to be replaced or the second bearing needs to be taped in further. A lose or worn center spacer can cause the bearing to be side loaded in the opposite direction after the axle is torqued down (See fig 3).

Kawasaki_KLX140_0786

Install the snap rings or bearing retainers as required.

ALL-BALLS_0007

The installed bearings should rotate as smoothly and easily as it did before it was installed.

ALL-BALLS_0027

Apply grease to the lips of the new dust seals.

ALL-BALLS_0028

Install the seals with the markings facing out.

ALL-BALLS_0026

Press in the seals with a suitable driver with the same outside diameter as the seal. Drive the seal in so that it is flush with the hub or to a specified depth in the service manual.

ALL-BALLS_0029

Install the outer wheel spacers to their correct side of the hub.

ALL-BALLS_0032

Insert the outer spacers into the dust seals.

To make your bearings last longer- avoid pressure washing around the bearing seals for extended periods of time. Pressure washers will push water right around seals causing premature rusting of the bearings.

YZ450_2010_0934

INSTALL ALL BALLS RACING STICKER!

URLs in this post:

[1] Additional Service Information Resources: http://www.cyclepedia.com/manuals/online/cpp-all-balls/additional-service-information/

[2] ALL BALLS Racing: http://www.allballsracing.com/

Copyright © 2014 All Balls Bearings and Components. All rights reserved.